Casa > Notícies > Contingut

Problemes de qualitat de la galvanització en calent i causes de la ruta

Jun 04, 2019

Els recobriments galvanitzats en calent proporcionen una protecció contra la corrosió excepcional al substrat d'acer, però el seu acabat no sempre és llis o uniforme compintura, recobriment en polsoxerarditzant. En general, els recobriments galvanitzats s'especifiquen pel gruix del recobriment de zinc per a la resistència a la corrosió, i no s'especifica pel seu aspecte. Tanmateix, el comprador sempre pot especificar quines són les aparences no-confirmatives, i a continuació es mostren els exemples típics.

1. Esquiries de soldadura

Els mètodes de soldadura que no produeixen escòries, com ara la soldadura MIG, són preferibles. Si s'utilitzen elèctrodes de soldadura recoberts, tots els dipòsits d'escòria s'han d'eliminar amb cura de la soldadura. No és possible eliminar l'escòria de soldadura mitjançant el decapat normal, i qualsevol residu provoca la formació de punts negres durant la galvanització per immersió en calent-. Les esquitxades de soldadura, les escòries i els porus s'han d'eliminar sempre abans que comenci el pretractament de la galvanització, en cas contrari, la superfície de la galvanització es veurà molt rugosa.

acid trap.jpg

2. Trampa d'àcid

Steel structures should be designed to avoid narrow crevices or gaps. If lap welds must be used, they should be welded around the entire joint. In case of double-sided fillet welds, the weld must be continued over the ends of the steel material to prevent the penetration of acid into any conceivable crevice. Plus, it is important to avoid the formation of pinholes. If the gap between contact surfaces is larger than 100 cm², venting holes must be provided to avoid the risk of explosion. Since molten zinc is more viscous than acid, it will seal the opening during hot-dip galvanizing. Afterwards, the acid will create holes in the coating, and then the rust-colored liquid will run on to the surface and spoils the appearance. Therefore, once acid has penetrated a crevice, it is impossible to be removed.  



3.Pugues de drenatge

Drainage spike is a very common defect, and it can be greatly avoided by setting up a hanging angle close to 45 degree ,which can minimize drainage at the bottom of the workpiece. Hanging steel works with a horizontal angle is forbidden, which will cause excessive drainage spikes. Grinding of drainage spikes shall be handled carefully, and overgrinding shall be prohibited. 


drainage spikes.jpg

dross pimples.jpg

4. Grans d'escòria

Dross pimples are small zinc-iron crystals formed from iron reacting with molten zinc during galvanization process. Dresses are heavier than zinc, and they settle on the bottom of the zinc kettle where they are periodically removed every 2 weeks or 10days. If the dross is stirred up and mixed into the molten zinc, it will often get trapped in the zinc coating leaving marks like pimples on the galvanization surface. An excessive amount of pimples can indicate a poor coating, and the zinc kettle shall be cleaned soon before another shift starts. 


5. Tinció de cendres

Sometimes, ash is trapped inside areas and sticks to the outer side of the coating as the steelwork is lifted from the zinc bath. Ash may cause a light brown stain, a dull or dark surface appearance after removal. It has negative impact upon the performance of the galvanized coating, and it's possible to be repaired by zinc paint if its size is small. 

ash staining.jpg


striations, lumps and runs.jpg

6.Estriacions, grumolls i curses

Les crestes i línies més gruixudes que el recobriment galvanitzat proper són causades per velocitats variables de reacció del zinc amb la superfície d'acer a causa de les zones d'estrès a la superfície de l'acer o la presència d'àrees de soldadura o metall de soldadura amb metal·lúrgia alterada al metall original. Aquesta ocurrència es veu amb més freqüència en tubs d'acer iperfils d'acer enrotllats. There is no impact on coating performance, but it does have appearance issue. Please also be reminded that it's a bad practice to remove the lumps by angle grinder vigorously, and this could remove the whole zinc coating leaving the steel uncoated.   


7. Marques penjants

Hanging marks are almost impossible to avoid, but it's possible to adjust the hanging angle to minimize the hanging marks. And, it's also possible to use manual grinder to remove marks with care, and then repair them by zinc rich paint. 

hanging marks.jpg


galvanization flaking.jpg

8.Galvanització Descamació

Flaking is the separation of the entire zinc coating, including the iron zinc alloy layers from the underlying steel. It is also known as delamination or chipping and should not be confused with peeling where only the top pure zinc layer separates from the underlying zinc alloy layers. Flaking usually occurs in thicker than normal galvanized coatings (200 μm or more), especially when these coatings receive impact forces during handling. Excessively thick coatings generate high stresses at the interface of the steel and galvanized coating which causes the zinc to become flaky and separate from the steel surface. Flaking typically occurs near the edges and creates bare spots in the protective zinc coating and it should be repaired to ensure ongoing corrosion protection. If the area of flaking is small, it can be repaired; however, if the flaking area is larger than allowed by the specifications, the part must be rejected and re-galvanized. Flaking can be avoided by minimizing the immersion time in the galvanizing kettle and cooling of the galvanized steel parts as quickly as possible, and if possible using a different steel grade. Steels with phosphorous content greater than 0.025 percent can experience flaking after galvanizing, even when the silicon levels are satisfactory.


9.Peeling i delaminació

Delamination or peeling creates a rough coating on the steel where the zinc comes off. Many large galvanized structures and steel profiles take a long time to cool in the air, and the zinc coating continues to form zinc-iron layer after they have been lifted from the zinc bath. This continued coating formation leaves a gap between the top two layers of the galvanized coating. If there are many gaps formed, the top layer of zinc can separate from the rest of the coating and peel off the part. If the remaining coating still meets the minimum specification requirements, then the part is acceptable. If the zinc coating that remains on the steel does not meet the minimum specification requirements, then the part must be rejected and re-galvanized. 


10. Punts nus

Les taques nues, les zones no recobertes a la superfície d'acer, són un defecte de la superfície que es pot produir a causa d'una preparació inadequada de la superfície. Els punts nus poden ser causats per escòries de soldadura, sorra incrustada en peces de fosa, excés d'alumini a la caldera de galvanització o dispositius d'elevació que impedeixen que el recobriment es formi en una àrea petita. Per evitar punts nus, el galvanitzador ha de garantir que les superfícies estiguin netes i sense òxid després del pretractament. Les petites taques nues es poden reparar amb un esprai de zinc ric. Si la mida del punt nu o el nombre total de punts està per sobre dels requisits especificats per la norma ISO 1461, la peça d'acer ha de passar per tot el pretractament i galvanització de nou.

bare spots.jpg


mottling.jpg

11.Motllats

A mottled surface appearance is caused by uneven cooling rates of newly hot-dip galvanized articles after withdrawal from the zinc bath. During air cooling of the articles, the zinc-iron coating formation reaction, consuming the outer free zinc layer in the process, can continue for a short time as long as the steel stays about 550 Fahrenheit degree. Due to the fact that the galvanizing reaction continues on the interior portion and consumes the free zinc layer, but not the exterior potion of the steel, and this causes a nonuniform appearance of the zinc coating. However, this difference in appearance does not affect the corrosion protection of the galvanized coating, and this mottling surface is acceptable per ISO 1461 specifications. Therefore, to speed up the cooling process, quenching is recommended. But, the galvanizers shall be reminded that some designs might not be suitable for quenching as they have a tendency for warpage or distortion during quenching process. 

After galvanizing, the steel cools from a temperature of approximately 840 F to ambient temperature. If the steel is quenched, cooling takes place rapidly, but not all galvanizers have quench baths and quenching is not recommended on some designs due to the potential for warpage/distortion of the steel. When the newly galvanized steel is allowed to cool naturally (without quenching), it can take several hours for the steel to come down to ambient temperature. Thinner steel cools faster while thicker steel takes longer to cool. Sometimes an individual piece of steel will have different cooling rates. 


12.Acabat apagat

The most common reason for dull appearances is the chemistry of the workpiece, and the main elements of steel chemistry which most strongly influence the final appearance are silicon and phosphorous. Both elements are catalysts to coating growth, and the thicker coating is responsible for the differing appearance. In addition to producing thicker coatings, highly reactive steels tend to have a matte gray or mottled appearance instead of a typical bright coating.  


13.Mala reparació de la galvanització

Els treballs de reparació de galvanització són d'alguna manera tan importants com els treballs de galvanització en si, i hi ha pocs errors comuns que s'han d'evitar.

√  Overgrinding, removed the zinc coating completely
√  Ús d'un polvoritzador de baix contingut de zinc per reparar
√  El gruix de reparació de zinc no compleix el gruix requerit


poor repair of galvanization.jpg


Fabmann té un estricte control del procés de producció al seu lloctractament superficial del metall, i tenim enginyers de qualitat molt experimentats que tenen un coneixement profund sobre el pretractament de galvanització en calent, galvanització i reparació de galvanització. És per això que podem oferir una qualitat superior per a productes d'acer d'àmplia gamma commaquinari de suport de moll, bastidors personalitzats, suports angulars reforçats, perfils d'acer enrotllats, claudàtors del pal de senyalitzacióisuports de gàbia per a la piscicultura to our clients. 


Enviar la consulta